Embossing
01 / 04
Embossing
A raised boss or bead is formed into the sheet in one stroke — stiffening a panel or fixing a locating point without removing any material.
Precision sheet metal parts, built to your drawing.
Blanking, punching, bending and plating under one roof — one vendor accountable for the whole part, from raw coil to finished coat.
MaterialGalvanized Steel
Thickness1.2 mm
Tolerance±0.1 mm
Operations
Four operations.
Four operations.
One continuous line.
Follow a single blank from coil to finished coat — blanked, punched, bent and plated, in the order the part actually moves across the floor.
01 / 04
Blanking
A steel strip feeds onto the line. Press 01 shears the outer profile from the sheet in a single clean stroke.
02 / 04
Punching
Press 02 pierces every hole and slot in one hit. The offcut slugs drop clear through the die.
03 / 04
Bending
Press 03 forms the centre band down and rotates both flanges up in one linked stroke. The part leaves the die at its final angle.
04 / 04
Plating
A fine powder builds an even coat across every face, then a final pass brings the part up to a uniform satin finish.
Capabilities
Everything else
Everything else
the part needs.
Embossing, threading, notching and knurling — added to the same job, so a part leaves here finished rather than half made.
Materials
Matched to the part,
Matched to the part,
not the other way round.
Metals, alloys and engineering plastics — sourced to spec and run on tooling that suits them, whatever the drawing calls for.
Tight-tolerance sheet
Formed into enclosures, brackets and stamped body parts.
Specified where a clean, consistent surface finish matters.
Spring-temper stock
Pressed into electrical contacts, connectors and switchgear parts.
Specified where a part needs to flex, spring back and keep conducting.
Low-friction, corrosion-resistant
Machined into bushings, bearings and wear fittings.
Specified where two metal parts move against each other.
High-tensile, fatigue-resistant
Formed into clips, leaf springs and load-bearing fasteners.
Specified where a part is loaded and released, cycle after cycle.
Zinc-coated, weather-ready
Formed into outdoor enclosures, ducting and structural cladding.
Specified where the part lives outdoors and has to resist rust.
Heat & insulation rated
Cut and machined into switchgear bodies, handles and insulating mounts.
Specified where a part sits near heat and can't carry current.
Tooling
A part is only as good
In-house die design
Progressive &
Tool maintenance
First-article
A part is only as good
as the tool behind it.
Every component starts as a die, not a sheet. We design, build and maintain our own progressive and compound tools in-house — so tolerance, cycle time and tool life are settled long before your first production run.
In-house die design
& build
Tools are engineered and built on-site, station by station, before the first sheet ever runs.
Progressive &
compound tooling
One strip, many stations, a single pass — fewer handlings per part, and lower cost at volume.
Tool maintenance
& repair
Dies are serviced and re-ground in-house, so tool wear never becomes your delivery problem.
First-article
approval
Every new tool proves itself on a first-article sample before a full run is cleared.
Quality
Checked at every station,
Checked at every station,
not just at the end.
Inspection is built into the run, not bolted on at the end — and the whole system is certified to ISO 9001:2015.
Incoming material checks
Coil and sheet stock verified against mill test certificates before it's released to the floor.
First-article & in-process inspection
Every new tool is sampled and measured before a full run starts, then re-checked at intervals through it.
Calibrated gauging
Dimensions confirmed with calibrated plug, ring and fixture gauges at the press, not only at final QC.
Final inspection & traceability
Each lot is checked, recorded and traceable back to the raw material batch before it ships.
Profile
Customer and quality
Customer and quality
first, since 1999.
A full-service manufacturer of sheet metal parts, fabricated assemblies and pressed & stamped components for original equipment manufacturing — every part built to your specification, never pulled off a shelf.
- 1999Founded
- ISO 9001:2015Certified QMS
- OEMSupply partnerships
Pressed and stamped components, run on presses and tooling set up to work from your drawing rather than a fixed catalogue.
The industry around us has changed a great deal since 1999 — faster cycles, tighter tolerances, far less patience for a rejected lot. What hasn't changed is the order of priorities the company was built on: customer first, quality never negotiable.
Contact
Send us the drawing.
Call, message on WhatsApp, or email it across — we'll come back with a price and a lead time.
Plot No. 118, Industrial Area‑4, Dabua Pali Road, Faridabad 121001, Haryana